• Power handling up to 5.0 Amps (according to heatsink)
• For 7.4 Volt LiPo batteries (PowerBox Battery) or 5 NC or NiMH cells
• Two independent linear voltage regulators, supplying 5.90 Volts
• Two independent electronic switches
• Two volt controller ( in 4 steps ) for each battery NEW
• Two Low voltage memory for both batteries NEW
• SET button for On / Off switching protection
• LED indicators for both power circuits
• Operating voltage range 4.0 to 9.0 Volts
• Temperature range -10?to +75?C
• Voltage loss approx. 0.35 Volts
• Weight only 35 grammes incl. all cables

Operating instruction (PDF 2,04 KB)

... more information about the PowerBox Sensor.

Certification (PDF 40 KB)

Test report (PDF 1,65 MB)

¡@

• Power handling up to 2 x 20 Amps
• For 4-cell or 5-cell NC or NiMH batteries; cell count freely selectable using "jumpers"
• Double "low-drop" voltage stabilisation of the receiver current at 4.0 A
• 7 channels remotely accessed from the receiver
• 7 two-way signal amplifiers
• 24 servo sockets on the backer
• Interference suppression for all 24 servo inputs (no ferrite rings required)
• Two independent, IC-controlled voltage monitors (LED chains)
• Two external ultra-bright warning LEDs
• Minimum voltage memory (low voltage memory) for both batteries, can be read individuall
• Operating voltage range 4.0 to 8.0 Volts
• Temperature range -10?to +55?C
• Voltage loss approx. 0.25 Volts
• Current drain 25 mA
• Weight only 122 grammes

Operating instructions (PDF 209 KB)
 
New Version: Supplement sheet for
PowerBox 40/24 Professional (PDF 88 Kb)
 
Certification (PDF 39 KB)

Accessories (included)

• Double linear voltage stabilisation for receiver and servos, supplying 5.90 Volts
• Power handling up to 2 x 20 Amps
• For 7.4 Volt LiPo batteries (PowerBox Battery) or 5 NC or NiMH cells
• 7 channels remotely accessed from the receiver
• 7 two-way signal amplifiers
• 24 servo sockets on the backer
• Interference suppression for all 24 servo inputs (no ferrite rings required)
• Independent, IC-controlled voltage monitors (LED chains)
• Two external ultra-bright warning LEDs
• Minimum voltage memory (low voltage memory) for both batteries, can be read individually
• Two integral electronic switches, controlled by the SensorSwitch
• Operating voltage range 4.0 to 9.0 Volts
• Temperature range -10?to +55?C
• Voltage loss approx. 0.35 Volts
• Current drain 25 mA
• Weight only 148 grammes complete with all cables and SensorSwitch

	Vorteile der PowerBox Competition gegenüber ähnlichen Produkten.
Operating instructions (PDF 881 Kb)   The SensorSwitch (PDF 118 KB)   Certification (PDF 39 KB)

¡@

• with double linear regulation of the servo voltage
  
• with separate, double-regulated voltage for both receivers
  
• with double battery monitoring by means of LED chains
  
• with signal amplification for each servo socket
  
• with RF suppression for each servo
  
• with suppression of servo feedback currents
  
• with dual electronic switches (SensorSwitches)
  
• with twelve freely programmable servo sockets (three channels)
  
• with redundant receiver system (RRS)
  
• with informative LCD screen for receiver analysis
  
• with switchable servo voltage: 5.9 Volts or 7.0 Volts
• 
  Operating instructions (PDF 9,29 MB)\

¡@